Technical & Industry Knowledge Base

Finishing concrete is not an easy job. During construction, workers’ hands, backs and knees are vulnerable to injury. The advent of the trowel allows construction workers to stand while the concrete is finished. Based on the size of the project, the number of people and the customer’s requirements for the surface layer, the construction party may consider purchasing a trowel. If you are a construction party specializing in concrete staining, staining or home improvement polishing, maybe you don’t need to buy a ride-on trowel (double disc machine). This type of troweling machine is not only expensive, but also has a high hardness of the ground after finishing, so the above-mentioned type of ground does not have such high requirements. In fact, a walk-behind trowel is sufficient to meet the work requirements of pulping and finishing small-area floors. Under what circumstances should you consider investing in a trowel? In general, construction area is an important consideration. "Even a small-area project can use a trowel, even if the project is only a few hundred square meters. As long as the construction area reaches 100 square meters, you must use a trowel, and if it exceeds 300 square meters, you have to consider using a small ride-on trowel From another perspective, the work efficiency of a single-disk trowel is equivalent to that of three construction workers using traditional manual finishing tools such as scrapers. It seems that the biggest advantage of the trowel is to increase the speed of application. But this is only a one-sided understanding of the advantages of the trowel. What the trowel gives is not a simple speed increase but the efficiency when dealing with large-scale construction. Furthermore, the troweling machine allows the construction party to choose a more appropriate time to start the machine when dealing with large-scale construction, instead of having to start early due to the need to consider the overall area of construction like traditional construction. Troweling machine operation steps: 1. Before use, check whether the motor, electrical switch, cable and wiring are normal and comply with the regulations, and install a leakage protector. 2. Before use, check and clean up the sundries on the wipe plate to avoid the whole machine from jumping when in use. 3. After turning on the power, carry out a test run, the blades will rotate clockwise and must not be reversed. 4. Operators should wear insulating shoes and gloves, and the cables should be picked up by auxiliary personnel, who should also wear insulating shoes and gloves. Pay attention to prevent electric shock accidents caused by the cable insulation layer being broken. 5. The troweling machine breaks down, and it needs to be shut down to cut off the power before it can be repaired. 6. The trowel should be stored in a dry, clean and non-corrosive gas environment. The handle should be placed in the specified position, and no rough loading and unloading should be allowed during transfer. Construction Notes: 1. During construction, pay attention to the temperature of the motor reducer box not exceeding 80° 2. The engine oil in the turbine box needs to be checked frequently. If the oil level is lower than the oil level, please refuel in time. After each use, the equipment should be cleaned in time, especially the smears should be stored in a dry, clean and non-corrosive environment. When the smear is worn to 30mm on one side, loosen the nut, turn the smear around and re-tighten the screw to achieve the purpose of two pairs of use. Angle of smear Rotate the hand wheel to adjust the angle of smear to achieve the ideal effect of rough smearing. If you need to shut down during construction, please turn off the power in time. When the gasoline engine stops, press the switch on the handle in time to stop. The ground effect after the troweling machine is more uniform, the construction speed is faster, and the operation is more convenient. Working with a hand-held spatula for a long time will easily fatigue the knees, shoulders and elbows of the construction workers, which will affect the construction effect. To put it simply, the use of a trowel makes the difficult operation easier, and it is the best equipment for finishing the floor.

With the continuous increase of domestic labor costs, engineering construction enterprises are increasingly demanding laser machinery with high efficiency, short construction period and low cost. The car-mounted laser leveling machine is convenient and quick to operate, suitable for different engineering needs, and has become the mainstream nowadays. The VANSE brand YZ25-4 four-wheel concrete laser leveling machines produced by Shandong VANSE Machinery are convenient and quick to operate, suitable for large-area paving, and have better compaction effects. Pay attention to the following aspects when purchasing a car-mounted laser leveling machine: 01 Look at the model: it is mainly selected and determined based on the construction site and area. 02 Look at the effect of the machine. 03 Leveling speed 04 Leveling accuracy requirements 05 Look at the manufacturer: the strength of the manufacturer directly affects the quality of the equipment. 06 Look at the price: If the price of a machine is too lower than the average price of the industry, buyers should be alerted. Under the condition of not achieving large-scale production, too low price does not mean low profit, but low cost, and low cost will directly affect the life and use effect of machinery, and even implies that enterprises There will not be too much investment in after-sales and R&D. Don't just look at the price because you don't know much about the technology. In the end, the gain outweighs the loss and you have to buy it again. Not only wasted money, but also delayed their own production. 07 Look at safety: when choosing a laser leveling machine, the braking performance and operation safety of the laser leveling machine should also be fully considered. The parts of VANSE mechanical laser leveling machine are all produced by large-scale manufacturers in advanced countries such as Germany and the United States. The production process is strictly in accordance with national standards, enterprise standards, and quality control assurance systems to ensure that product quality meets or exceeds enterprise standards and related According to the requirements of national standards, it has won the trust and praise of users for its excellent quality, excellent performance and superior cost performance. Shandong VANSE Machinery series products have been widely used in factories, with customers all over the country, inside and outside the Great Wall, and have been recognized by many engineering project partners and customers such as workshops, underground garages, floors, access bridges, square floors, logistics and warehousing.

The construction machinery industry is becoming more and more mature, and various types of construction machinery are more and more commonly used in my country's consumer market, especially this year, concrete laser leveling machines are more and more recognized by customers. As the leader of concrete laser leveling machine, the concrete laser leveling machine produced by Shandong VANSE Machinery can realize large-scale construction, and completely eliminate all the "common quality problems" caused by the secondary method by solving the concrete surface layer at one time . It has truly achieved the effect of "three super" floors that are flat, clean, dense, high-strength, one layer as a whole, cost reduction, construction period shortening, and absolute durability. Shandong VANSE mechanical concrete laser leveling machine has several advantages compared with traditional laser leveling machines: 1. Laser alignment, high precision and low error. Traditional process leveling requires support formwork to control the elevation of the ground and pull the control line. The elevation error is large. The levelness and flatness of the entire floor cannot be guaranteed. Using a laser point-to-point emitter, it is suitable for large-area one-time paving. There is a laser measurement and control system to control the elevation in real time. There is no need for pulling wires for leveling, and there is no need for side plates in the middle to control the elevation of the ground. In this way, the elevation error caused by the vibration of the formwork (channel steel) during the construction process is avoided, and the elevation error caused by traditional manual block formwork is also reduced. 2. Reduce labor costs and double the efficiency. Traditional construction involves a large number of workers, requiring support formwork (channel steel), spotting, and paving. About 20 people are needed. The daily construction area is 700 square meters. The total number of people who use the concrete laser leveling machine is reduced by more than half compared with the traditional process. Can be operated by one person. The daily construction area is 2500-3500 square meters, which greatly reduces labor costs. 3. Better flatness and integrity. Traditional craft construction, one day of formwork and one day of watering, can only be skipped one by one for construction, which has great limitations, cannot be continuously operated, and the integrity is not good, which is likely to cause cumulative errors in construction joints. Concrete laser leveling machine can pave a large area of the floor at one time, with higher efficiency and integrity. The completion of the entire floor will make the ground integrity better, which is completely impossible for traditional construction.

Concrete laser leveling machine is widely used and is an advanced machine used to super-level and level concrete floors. Its application scope can be roughly divided into two categories: indoor floor engineering and outdoor floor engineering. These two types have small subdivisions. The following is a detailed introduction to the subdivision range of concrete laser leveling machines, as well as an introduction to such projects that VANSE Machinery's products have done. Nowadays, concrete laser leveling machines are more and more widely used, and the specific scope of application can be divided into two categories: 1. Indoor floor 1) Industrial plants, workshops, automated three-dimensional warehouses: VANSE Machinery has done such projects as Harbin Haier workshop, Beijing Benz workshop, Baoding Great Wall Motor No. 5 spraying workshop, Shandong Classic Group steel structure production line workshop and other projects. 2) Clean workshops for electronic appliances, food materials, medicine, etc.: Such projects that VANSE Machinery has done include: Suzhou Samsung Electronics Factory, Shandong Xingda Ecological Winery, Shandong Baisheng Biological Workshop, Shandong Yuda Medical Workshop and other projects. 3) Large warehouse supermarkets, logistics centers, exhibition centers, etc.: Such projects that VANSE Machinery has done include: Xi'an Fuju Home Plaza, Shenzhen Wal-Mart Supermarket, Wuhan Vipshop Logistics Park, Guangxi Convention and Exhibition Center, Tianjin Yupei Logistics Park and other projects. 2. Outdoor floor 1) Wharf, container yard, freight yard: Such projects that VANSE Machinery has done include: Hubei Xiangzhou Industrial Park, Shanxi Shenlong Energy Coking and other projects. 2) Airport runways, aprons, and parking lots: Such projects that VANSE Machinery has done include: Shandong Xinbaihui underground parking plant, Changchun FAW-Volkswagen parking lot, Hebei Hualian Supermarket large-scale underground parking lot, Sichuan Wanda Plaza large-scale underground parking lot, Hubei Xiangyang Dongjin Century City underground parking lot and other items 3) Squares, residential grounds, municipal roads, etc.: VANSE Machinery has done such projects as: Nanjing Huawei Electronics Company Floor, Shenyang Electronics Factory Floor Integration, Sichuan Hualian Plaza, Hubei Xiangyang Dongjin Century City and other projects. Shandong Yanzhou VANSE Machinery Technology Co., Ltd. is the only high-tech enterprise in China that integrates R&D, manufacturing, sales and technical services, specializing in concrete laser leveling machines. The use of "Leilong" brand concrete laser leveling machine can reduce high-intensity labor by about 60%, save about 50% of construction costs, shorten about 50% of construction period, and increase the strength and compactness of the floor by about 25%. The company has always been "people-oriented, technology-leading, honest management, creating a well-known brand" as its purpose, providing customers with reliable products, perfect services, common development, and creating success.

Concrete construction is generally leveled manually, and the appearance of laser leveling machines completely liberates the inconvenience of manual operation. It greatly reduces the labor cost for the construction site, and has a significant improvement in the leveling effect of the concrete. Therefore, mechanized operations in this era can have a great impact on the construction industry. Concrete laser leveling is a scientific and reasonable design, and there is no need for manual assistance in the operation of the equipment, which is the convenience, science, technology, etc. in the design process. Of course, the laser leveling equipment used in different construction fields is different. Because the concrete laser leveling equipment has a variety of models and sizes in the production process, it has a wide range of uses. All of these need to improve the advantages and technical characteristics in this aspect during the leveling process, so as to be able to occupy an advantage in the industry and improve the brand characteristics. As in concrete laser leveling, it must be seen through the concrete construction process. This is the key to technological progress. It has full advantages and status in the field of various leveling and leveling equipment, and has been recognized and trusted by more builders, so it has been widely promoted in construction sites across the country. Issues that should be noted: (1) Due to the high construction efficiency, the later cutting must keep up. Generally, each laser leveling machine is equipped with 7-8 cutting machines to meet the requirements. (2) In the early stage, plastic film should be used for maintenance, and non-woven fabric should be covered after cutting. (3) During the construction process, due to the lateral pressure of the concrete, the steel mesh is easy to displace horizontally. For this reason, an isolation bench is placed directly on the adjacent steel mesh, so that the horizontal displacement of the steel mesh can be effectively controlled, and the bench can be used repeatedly. Advanced equipment such as laser leveling machines are especially suitable for projects such as docks, storage yards, expressways, airports, large squares, parking lots, and municipal roads that have relatively simple shapes, large amounts of action, and high construction quality requirements. DETAIL IMAGES

The construction floor construction industry is currently developing relatively fast, and with it, the use of construction machinery such as laser levelers is becoming more and more frequent. So, why must we recommend this kind of equipment for everyone among the many construction machinery? In fact, there are certain reasons. Next, let us take a look at the introduction of the following articles! Compared with traditional laser leveling machines, laser leveling machines have several advantages in building floor construction: 1. Reduce labor cost and double increase efficiency: There are many people involved in the construction of the traditional craft, which requires support formwork (channel steel), spotting, and paving. About 20 people are needed. The daily construction area is 700 square meters. The total number of people who use the concrete laser leveling machine is reduced by more than half compared with the traditional process. Can be operated by one person. The daily construction area is 2500-3500 square meters, which greatly reduces labor costs. 2. Laser alignment, high precision, low error: The traditional process of leveling requires support formwork to control the elevation of the ground and pull the control line. The elevation error is large. The levelness and flatness of the entire floor cannot be guaranteed. It adopts laser point-to-point emitter, which is suitable for large-scale one-time paving. There is a laser measurement and control system to control the elevation in real time. There is no need for pulling wires for leveling, and there is no need for side plates in the middle to control the elevation of the ground. In this way, the elevation error caused by the vibration of the formwork (channel steel) during the construction process is avoided, and the elevation error caused by traditional artificial block formwork is also reduced. 3. Better flatness and integrity: Traditional craft construction, one day of formwork and one day of watering, can only be skipped one by one for construction, which has great limitations, cannot be continuously operated, and the integrity is not good, which is easy to cause cumulative errors in construction joints. The laser leveling machine paves a large-area floor at one time, with higher efficiency and integrity. The completion of the entire floor makes the ground integrity better, which is completely impossible for traditional construction. 4. The ground is denser and more uniform: The 4000 times per minute high-frequency vibrator allows the leveling head vibrator to produce uniform high-frequency vibration, making the concrete floor more dense and uniform. As the leader in the design of concrete laser leveling machines, the laser leveling machines produced by our company can realize large-scale construction. By solving the concrete surface layer at one time, all the "common quality problems" caused by the secondary method are completely eliminated. We will continue to provide customers with reliable products and better services.

When the concrete laser leveling machine performs operations on the road surface, some parts of the equipment may overheat due to the increase in temperature, which will affect the correct leveling effect of the equipment. So, how should the temperature of the leveling machine be controlled during work? Next, let's take a look at how our company's technicians teach you how to control the temperature of the leveling during operation! How to control the temperature during leveling operation? First of all, controlling the temperature of the leveling machine is one of the keys to ensure the quality of leveling. When the equipment is being leveled, it should meet the requirements of relevant standards according to the type of asphalt, label, consistency, ambient temperature, and leveling thickness. Secondly, when the construction temperature of expressways and first-class roads is lower than 10°C, and the construction temperature of other grades of roads is lower than 5°C, leveling is not suitable. If it is necessary to carry out leveling work, the temperature of the road leveling machine should be increased, and there are also low-temperature leveling requirements that meet the regulations. After the plate is heated and leveled, it is pressed immediately to shorten the length of the press. Finally, remember that during leveling, the requirements of relevant standards should be met according to the type of asphalt, label, consistency, ambient temperature, leveling thickness, etc. In this case, it is relatively simple and easy to control the temperature. Precautions for leveling machine: 1. After finishing the leveling operation, carry out the routine maintenance work according to the content of the routine maintenance procedure. 2. The working devices and moving mechanisms of the leveling machine that are in direct contact with the asphalt mixture during operation, after the operation, spray with diesel oil and then run for a period of time to remove the residual asphalt on it, so that it can run freely and rotate flexibly. It is forbidden to spray diesel oil on the electric control system and helix to prevent fire and combustion when electrified. 3. After leveling the two-ash soil, wash it with water to wash off the white material. After washing, use waste hydraulic oil to lubricate the moving parts of the scraper conveyor chain, and apply anti-rust oil to the piston rod. Be careful not to allow water to wash into the electrical appliances and bearings to prevent short circuits and foreign objects entering the bearings. 4. Clean and check the elevation adjustment device of the slope gauge, and lubricate the lead screw with grease. Apply grease to the slide rails of the floating arm. Grease each oil filling point until the seam overflows. For levelers with oil filling cups, observe the consumption and fill them up at any time. Have you learned all the above? If you want to know more about concrete laser leveling machine, please continue to pay attention to this website!

With the addition of concrete laser leveling machines in the construction industry and road construction industries, there has been a qualitative leap in both quality and speed, and it has also saved a lot of costs for users. However, in the face of high-frequency use, users cannot ignore the cleaning of the equipment. This step must not be sloppy. Let's take a look at how to clean the leveling in a few steps! 1 The liquid crystal surface on the laser leveling machine body also needs to be cleaned. You can use organic resin or lens cleaning cloth to wipe off the dirt. If there is too much dirt, it can be removed with a lens cleaning solution. 2 After the laser leveling machine is constructed, there will be a lot of dust and mud. First of all, the dust on the laser leveling machine should be wiped clean, and the dirt and oil stains should be wiped clean with tissue paper or cotton cloth. 3 If the laser signal is lost during the construction of the laser leveling machine, the machine needs to be restarted, and the interval should be more than ten seconds. 4 If there are too many stains, you can use a soft cloth to soak in water diluted with a neutral detergent, wring it out and clean it. The best laser leveling machine manufacturers remind you not to use volatile oil, thinner, gasoline, etc. Chemical cleaning wipe. The laser leveling machine uses a scraper to take away the raised concrete and initially level it to reach the elevation required by the design. The hydraulically driven vibrating motor vibrates at a frequency of 4000 times per minute, driving the entire vibrating plate to vibrate the concrete together. The leveling of the laser paver does not need to pull the control line, nor does it need the side formwork to control the ground elevation, but is controlled by the laser measurement and control system on the laser leveling machine in real time. As long as the laser transmitter is not disturbed, no matter where the laser leveling machine moves Wherever it is, it can be ensured that the overall elevation of the paved ground will not be affected. The concrete ground laser leveling machine is to spread the mixed concrete along the subgrade according to the given thickness, width and road type requirements, and then complete the construction of paving the concrete road surface through the operation procedures of vibrating, leveling and troweling. mechanical. The working device of the concrete floor laser leveling machine generally consists of a distributor, a scraper, a vibrator (including a vibrator and a vibrator), a leveling machine, a trowel and other devices. At the same time, it also requires the organic cooperation of the frame, walking mechanism, manipulation control system and other auxiliary mechanisms. Some models integrate all the devices into one, and some are divided into two or more independent stand-alone machines.

VANSE laser leveling machine training and after-sales service after purchasing the machine Shandong VANSE Machinery Co., Ltd. not only sells laser leveling machines, but also assists customers to complete projects and meet high-standard construction requirements. The so-called assisting customers to do projects means that our company's personnel will operate in the early stage of construction, and provide systematic training to the customer's construction personnel at the same time, which can be roughly divided into the following three steps: 1. The first job after the machine is sold is the pre-construction work. Our staff will explain the construction process, installation, and commissioning of the machine to the customer in detail: 1) After the base level is processed, the equipment of the laser leveling machine is adjusted, and the fixed reference level is drawn according to the original level point; the plastic film is laid, the steel mesh is bound (according to the design requirements), and the side formwork is supported; the laser transmitter is erected , introduce the floor level into the laser leveling machine according to the original benchmarking point. 2) Convey concrete, use commercial concrete, and transport it to the construction site with concrete trucks. 3) Scale calibration Use a hand-held receiver to check the floor elevation, introduce the elevation into the laser leveling machine, and adjust the reference point (±0.00) on the leveling machine. 2. Prepare well for the construction. During the construction, we will explain in detail the training and operation of the machine, the on-site construction, and the solutions to the problems that are easy to occur during the learning construction: 1) Concrete paving, within the effective construction range of the leveling head of the laser leveling machine, the concrete is initially leveled manually to a height of 1-2 cm higher than the floor level (the specific height depends on the slump of the concrete), and then the concrete The laser leveling machine completes the vibration, compaction and leveling work at one time. 2) Troweling and finishing. When the poured concrete reaches initial setting, it is polished by a trowel machine, and then manually troweled and finished. 3. After construction, we will explain to customers in detail the maintenance of the machine, different types of engineering construction methods, and different standard construction methods: 1) After each construction, you need to use the arm lift button to manually lift the machine head, and then exit the construction site. During this process, be careful not to push the machine when the vibration leveling part is in contact with the ground, otherwise it is easy to cause damage to the vibration plate. Moreover, after the construction is completed, it is necessary to flush the machine with a high-pressure water gun in time to prevent the water gun from being directly aimed at the mesh part of the fuselage for washing, so as to prevent water from entering the inside of the fuselage and causing problems such as short circuit of the machine circuit. 2) In addition, pay attention to the maintenance of the concrete floor. After the concrete is troweled, it is not allowed to move heavy objects on the floor for at least 7 days, and it should be kept in a moist curing state. In order to achieve a good maintenance effect, the surface should be covered to isolate the concrete from the outside. During the maintenance period, when the strength of the surface concrete does not meet the requirements, it is strictly forbidden to use people; the cutting seam should be in accordance with the design requirements, and the surface treatment of the floor should be completed. It is to be carried out later, that is, to ensure that it is carried out before the final setting of the concrete. The spacing, width, and depth of the cuts must meet the requirements of the design and construction specifications; the joints should be filled and protected until the concrete reaches its strength before it can be used. Our Shandong VANSE Machinery has a standard, that is, the customer's construction personnel are proficient in operating the machine, can do the on-site construction well, and complete the three training procedures to meet the standards of Party A and the customer's approval, and our company's staff can leave the site.

LASER LEVELING MACHINE – INSTRUCTIONS FOR USE With the continuous development and progress of the construction floor industry, the concrete laser leveling machine has become an indispensable mechanical equipment in modern buildings. The concrete laser leveling machine is a kind of super-flat and level ground Excellent machinery. In the past few years since its inception, the sales of Shandong Wanshi Concrete Laser Leveling Machine have continued to increase. And with the gradual recovery of the economy, the prospect of the entire laser leveling machine industry in the future is generally optimistic. Modern large-scale storage and logistics, squares, municipal roads, parking lots and other construction fields directly stimulate the demand for concrete laser leveling machines. The market demand for laser paving paver equipment is huge. During the use of the concrete leveling machine, pay attention to the following items so that the machine can serve you better: Due to the high efficiency of construction, the cutting seams in the later stage must keep up. Generally, each laser paving and leveling machine is equipped with 7-8 cutting seams to meet the requirements. The speed of the laser leveling machine should not be too fast during the leveling operation. Initial leveling should be carried out before concrete leveling, and the concrete after initial leveling should be higher than the established elevation. In the early stage, plastic film should be used for maintenance, and non-woven fabric should be covered after cutting. Pay attention to avoid obstacles when installing the laser transmitter. During the construction process, due to the lateral pressure of the concrete, the steel mesh is easy to displace horizontally. Therefore, an isolation bench is placed directly on the adjacent steel mesh, and the horizontal movement of the steel mesh is effectively controlled, and the bench can be used for turnover. Shandong VANSE Machinery is a professional concrete laser paving and leveling machine manufacturer integrating R&D, production and sales. The concrete laser leveling machine and other high-tech products produced by the company can reduce about 60% of the high-strength Labor force, saving about 50% of construction cost, shortening about 50% of construction period, increasing the strength and compactness of the floor by about 25%, levelness and flatness exceeding the national standard, and the completed "three super" floor reaching the international standard First class.

Why has the concrete laser leveling machine become the mainstream leveling equipment? Concrete laser leveling machine is usually used in large-area floor construction, the ground elevation is easy to control, and the error of ground flatness is extremely small; due to the use of laser point alignment, the entire floor only needs 1-2 reference point elevations, which can reduce many factors. The error caused by the benchmark points. The laser transmitter is arranged independently, and the floor elevation is always controlled by the plane formed by the rotating beam emitted by the laser transmitter. As long as the laser transmitter is not disturbed, no matter where the concrete laser leveling machine goes, it can ensure the smoothness after paving. The overall elevation of the ground is not affected, so that large-area one-time paving can be realized in the floor construction, and the levelness and flatness of the entire floor can be guaranteed. The elevation of the concrete laser leveling machine is controlled by the laser measurement and control system in real time. There is no need to pull the control line for leveling, and there is no need for supporting side formwork to control the ground elevation, thus avoiding the vibration caused by the formwork (channel steel) during the construction process. The elevation error also reduces the elevation error caused by the traditional artificial block formwork. Now in some precision instruments, equipment production factories, aircraft manufacturing and maintenance workshops, etc., the quality of the floor is very high. It is mainly reflected in the high requirements on the flatness of the floor, and the floor surface is required to be wear-resistant, durable in use, and the maintenance cycle is extended. For example, in some large-scale foreign-invested logistics warehouses, in order to make full use of the land, the shelves in the warehouse are stacked very high, and some even reach tens of meters. The center of gravity is skewed and unstable, and the impact during driving will cause the forklift to shake, and there is a danger of the cargo being scattered or the forklift overturning. At the same time, the impact of the bumps of multiple forklifts on the ground will cause an earthquake effect, which is very unsafe for high-level cargo stacking. . Floor hollowing, cracking, and non-wear resistance will increase the number of floor maintenance, increase floor maintenance costs, and cause downtime losses; floor cracking will increase maintenance costs, and may also lead to abandonment or reduced utilization. For high-precision instruments and equipment production lines, if the floor is uneven, it will affect the installation of the equipment, and the gap between the equipment base and the ground may cause slight vibration during the operation of the equipment, which not only affects the life of the equipment, but also affects the product quality. For the above-mentioned floors with special requirements, especially large-scale entire floors, traditional construction techniques and methods are difficult to meet the requirements. For example, in terms of construction techniques, advanced construction equipment is used: concrete laser leveling machine, double-disc grinding machine , Dry cutting can not only shorten the construction period, but also ensure the construction quality to a large extent. This high-grade ground can guarantee normal use for more than 20 years, which can greatly reduce the use and maintenance costs. With the increase of large-area and high-quality floor projects such as modern industrial plants, convention centers, squares, airports, etc., the application of concrete laser leveling machines in large-area floor construction will increase.

Four reasons for you to choose laser leveling machine! We choose the laser leveling machine in addition to the fast leveling of the equipment and the high degree of automation. After manual adjustment of the height, the equipment can operate by itself, integrating leveling, leveling, tamping, and compaction. All the work can be done. It can be completed at one time, which is very suitable for the leveling needs of large sites. (1) The leveling principle of the laser leveling machine is realized under the automatic control of the computer by using precision laser technology, closed-loop control technology and highly precise hydraulic system. This is the most prominent difference between it and other floor construction processes. specialty. (2) The leveling principle of the laser leveling machine is to rely on the leveling head driven by hydraulic power, cooperate with the laser system and the computer control system to complete the leveling work while automatically leveling. The leveling head is equipped with an integrated scraper, vibrator and leveling plate, which integrates all leveling, leveling, vibration and compaction work, and completes it at one time. The computer control system automatically adjusts the elevation 10 times per second in real time, and the vibration frequency of the vibrator with a balanced design reaches 3000 times per minute. (3) The laser transmitter used to control the ground level is arranged independently, so that the level of the ground is not controlled by the template, and no cumulative error will occur. (4) The laser leveling machine can also automatically control the longitudinal and transverse slopes, which is also completed by the laser system, computer system, hydraulic system, and mechanical system. For complex-shaped ground with high requirements such as drainage, a three-dimensional special-shaped ground treatment system can also be selected to achieve it. The laser leveling machine is developed according to the increasing demand for ground quality such as strength, flatness, levelness, etc. of modern industrial plants, large shopping malls, warehouses and other large-area cement concrete floors. Using Shenlong laser leveling machine to pave and level the cement concrete floor is much better than the ground paved by conventional methods-the ground flatness and levelness are increased by more than 3 times, and the compactness and strength are increased by more than 20%. At the same time, it can also improve work efficiency by more than 50%, and save about 35% of labor. In addition, it can easily place high-strength concrete, low-slump concrete and fiber cement. Its laser system is equipped with a variety of automatic control components to monitor the elevation of the leveling head in real time at a frequency of 10 times per second to ensure that the levelness and levelness of the ground being paved are effectively controlled. At the same time, the vibrating frequency of its powerful vibrator reaches 3000 times/min, which ensures that the concrete is vibrated and compacted, so that the entire paved concrete matrix is homogeneous and dense.