Technical & Industry Knowledge Base

Can good maintenance habits really prolong the service life of laser levelings? Laser leveling machine is a great helper for leveling machinery in construction, but road builders can always feel that after several years of use, the equipment is far from being as flexible and convenient as before. What is the reason for this? Many users only know the surface and don't know the reason, so they can only procrastinate and procrastinate. When they use it next time, they will regret it. During the use of the laser leveling machine, due to the different working intensity, there may be some small faults after use. At this time, road builders should pay attention to it. After use, it is necessary to properly do some daily maintenance for the machine. This can prolong the service life of the machine equipment. 1.Check the connection and fastening of the parts of the laser leveling machine, whether the connecting bolts are loose or broken, and tighten or replace them if necessary. Check for leaks and eliminate leaks in various parts in time. Pay attention to the quantity of engine oil, fuel, coolant and hydraulic oil, and add new oil to the scale indicated on the oil mark as required. Whether there is proper amount of grease in the centralized lubrication device. 2.Be careful not to work under the maximum load that the machine can bear, and use the machine within your ability. As a laser leveling machine manager, when appointing an operator, the laser leveling machine random data and operation manual should be handed over to the operator, so that they can normally grasp the mechanical properties and operating procedures, and should not arbitrarily hand over the relevant information Buckle it down. 3.It is necessary to ensure the uniform addition and subtraction of the mechanical load as far as possible, so that the machinery is in a relatively gentle load change. Specifically, it is necessary to increase and decrease the throttle more evenly to prevent the engine and working devices from fluctuating greatly. 4.There will be a lot of dust and mud on the laser leveling machine after construction. First, wipe off the dust on the laser leveling machine, and wipe off the dirt and oil stains with tissue paper or cotton cloth. 5.If the laser signal is lost during the construction of the laser leveling machine, the machine needs to be restarted, and the interval should be more than ten seconds. 6.If there are too many stains, you can use a soft cloth to soak in water diluted with a neutral detergent, and then wring it out to clean it. The manufacturer of Wanshi laser leveling machine reminds everyone not to use volatile oil, thinner, gasoline and other chemicals to clean and wipe. . Developing a good habit of operating the laser leveling machine will be of great help to the construction and storage of the laser leveling machine in the future. This will not only improve the work efficiency, but also extend the service life of the machine to a certain extent .

THE NECESSITY OF CHOOSING A LASER LEVELING MACHINE!!! The laser leveling machine uses laser to level the ground, which has higher accuracy and smaller ground error after paving. Moreover, the construction efficiency of this kind of equipment is basically more than three times that of manual work, and one piece of equipment can be done, saving labor investment and reducing capital cost investment. Definition of laser leveling machine: A device guided by a laser for leveling and leveling fresh concrete. A concrete construction method that uses a laser leveling machine to pave and level the newly poured concrete. Advantages of concrete laser leveling machine: 1. High construction quality The laser leveling machine can level the ground, which can significantly improve the flatness of the ground. For the ground constructed by the laser leveling machine and the traditional method, 22 points are detected (one point every 5mx4m), and the average flatness is 1.3mm and 4.1mm respectively. Laser leveling The leveling quality of equipment such as leveling machines is more than three times higher than that of traditional methods. The application of equipment such as laser leveling machines can realize large-scale construction, reduce a large number of construction joints, reduce the slump of concrete, ensure the strength of concrete, and make the ground integrity good and cracks are not easy to appear. 2. Fast construction speed The use of laser leveling machines and other equipment to construct large concrete slabs improves the work efficiency by 3 times compared with the traditional beam vibrator method and saves 30%. The construction area per hour is more than 300㎡, and the daily workload can be completed from 3000㎡ to 5000㎡. Work efficiency is greatly improved. Of course, high-quality and efficient large-area overall floor construction requires not only a high-quality and reliable laser leveler, but also a fast and convenient spreader. Somero STS-11M spreader equipment eliminates a series of defects that affect the final aesthetics and quality of the floor, such as uneven spread, dust pollution, footprints, and color differences caused by traditional wear-resistant aggregate spreader, and truly achieves high efficiency. Wear-resistant aggregate one-time mechanized distribution. 3. Save manpower and improve industrial efficiency 1)Integrated leveling head: It is composed of scraper, vibrator, vibrating plate, stirring cage and other components. It integrates multiple processes such as stirring, leveling, vibrating, and vibrating, and is completed by the machine at one time. Improve efficiency and save labor. 2)The high-frequency vibrator with 4000 times per minute and the uniform high-frequency vibration of the leveling head vibrating plate make the concrete floor dense and can avoid ground cracks caused by stress concentration caused by deformation. It can effectively solve the problems of hollowing, shelling, cracking and inequality on the ground. 3)The leveling head can maintain the level of the construction under the double transformation of the undulating foundation and the slope of the ground. 4)The laser measurement and control system automatically controls the elevation: the design elevation of the top surface of the floor is automatically controlled by the laser machine computer, which can ensure very high ground flatness, and can directly achieve accurate leveling on the concrete layer, and the ground flatness is not affected by the vibration of the construction formwork Influence, there is no need to support the formwork in the middle, reduce the input of artificial materials, reduce the construction procedure, and speed up the construction progress. Finally, it should be noted that if you want to use a concrete laser leveling machine, you must choose a professional concrete laser leveling machine brand equipment and pay attention to the method of use. Without professional training, the construction efficiency may not be able to keep up, and the effect will be poor. Big discount.

What are the construction characteristics of laser leveling machine? The precision laser leveling machine is developed according to the increasing demand for ground quality such as strength, flatness, levelness, etc. of modern industrial plants, large shopping malls, warehouses and other large-area cement concrete floors. The leveled cement concrete floor is paved with the VANSE precision laser leveling machine, and the quality of the ground paved by conventional methods is much better – the flatness and levelness of the ground are increased by more than 3 times, and the compactness and strength are increased by 20% above. At the same time, it can also improve work efficiency by more than 50%, and save about 35% of labor. In addition, it can easily place high-strength concrete, low-slump concrete and fiber cement concrete. Its laser system is equipped with a variety of automatic control components to monitor the elevation of the leveling head in real time at a frequency of 10 times per second to ensure that the flatness and levelness of the ground for paving are effectively controlled. At the same time, the vibrating frequency of its powerful vibrator reaches 3000 times/min, which ensures that the concrete is vibrated and compacted, so that the entire paved concrete matrix is homogeneous and dense. Laser leveling machine features: 01 The leveling principle of the laser leveling machine is realized under the automatic control of the computer by using precision laser technology, closed-loop control technology and highly precise hydraulic system. This is the most prominent difference between it and other floor construction processes. specialty. 02 The leveling principle of the precision laser leveling machine is to rely on the leveling head driven by hydraulic power, cooperate with the laser system and the computer control system to complete the leveling work while automatically leveling. The leveling head is equipped with an integrated scraper, vibrator and leveling plate, which integrates all leveling, leveling, vibration and compaction work, and completes it at one time. The computer control system automatically adjusts the elevation 10 times per second in real time, and the vibration frequency of the vibrator with a balanced design reaches 3000 times per minute. The leveling accuracy is 40 extension meters and the control is below 3mm 03 The laser transmitter used to control the ground level is arranged independently, so that the level of the ground is not controlled by the template, and no cumulative error will occur. 04 The laser leveling machine can also automatically control the longitudinal and transverse slopes, which is also completed by the laser system, computer system, hydraulic system, and mechanical system. For complex-shaped ground with high requirements such as drainage, a three-dimensional special-shaped ground treatment system can also be selected to achieve it. The above was introduced by VANSE Machinery, I hope it can help you understand, if you have any questions, you can browse our website more, and you can also communicate with our technical staff.

What are the advantages of laser leveling machine? The laser leveling machine is developed according to the increasing demand for ground quality such as strength, flatness, levelness, etc. of modern industrial plants, large shopping malls, warehouses and other large-area cement concrete floors. Not only is it fast and compact, it saves labor input to a great extent and saves economic costs in disguise. Advantages of laser leveling technology: 01 Higher construction quality – the ground elevation and flatness of laser-level precision can be achieved. The floor elevation is automatically controlled by laser and computer, and the leveling unit is adjusted in real time through a two-way hydraulic cylinder (10 times per second), ensuring Precise leveling. 02 The density of concrete is increased by more than 20%, and the strength of concrete is improved, and it is suitable for dry hard concrete, fiber concrete and large aggregate concrete. 03 The laser emitter is arranged independently. The floor construction can be paved in a large area and can ensure the consistency of the ground elevation. The elevation is not controlled by the formwork, and there will be no cumulative error. 04 Compared with the traditional method, the construction joints of the floor can be greatly reduced, and the construction without separate warehouse joints can be achieved. The post-maintenance cost of the ground and the use of templates are also greatly reduced. Due to maintenance and formwork support, the sub-storage joints on the large-area concrete floor will have defects such as damage along the joints. These problems can be avoided by using laser leveling and joint cutting technology. 05 The integrity of the ground is better – it is very easy to achieve large-area overall paving. On the one hand, this overall paving technology can avoid problems such as easy hollowing and cracking caused by layered pouring of the floor, and on the other hand, it can reduce A large number of construction joints make the integrity of the ground better. This is not easy to do with other construction techniques. 06 The vibrating system of the laser leveling machine has a vibrating frequency of 3000 times per minute, which can avoid irregular cracking and other ills caused by uneven stress caused by uneven vibrating. 07 The construction speed is faster – the work efficiency is increased by 100-300% (200-400 square meters of paving work can be completed per hour, and an average of 1500-4000 square meters can be completed per day), and labor is reduced by more than 30%, especially suitable for Projects with tight construction schedule, large paving area and high quality requirements. 08 Save the cost of formwork and support formwork. The leveled cement concrete floor paved by the laser leveling machine is much better than the ground paved by conventional methods-the ground flatness and levelness are increased by more than 3 times, and the compactness and strength are increased by more than 20%. At the same time, it can also improve work efficiency by more than 50%, and save about 35% of labor. In addition, it can easily place high-strength concrete, low-slump concrete and fiber cement. Its laser system is equipped with a variety of automatic control components to monitor the elevation of the leveling head at a frequency of 10 times per second in real time to ensure that the levelness and levelness of the ground being paved are effectively controlled. At the same time, the vibrating frequency of its powerful vibrator reaches 3000 times/min, which ensures that the concrete is vibrated and compacted, so that the entire paved concrete matrix is homogeneous and dense.

What is the leveling speed of the concrete laser leveling machine? How's the effect? Concrete laser leveling machine is a kind of mechanical equipment for construction. Like many mechanical equipment, it is composed of multiple unit parts: motor, vibration head, body, etc. It is the reasonable combination of these parts that makes the performance of the whole machine become Like a powerful pressurized device, it is full of pressure. If we rely solely on manpower in our daily life, it takes a lot of experience and ability to deal with the smoothness of various grounds, bridge decks and construction equipment, so that people cannot do other things well. The performance of concrete laser leveling machine is as follows: 1. The combination of the equipment is good, it can be used in many coagulation projects, it is not affected by the environment and the size of the project, and has strong adaptability; 2. The concrete laser leveling machine has very good compression resistance. It can exert strong pressure on the working surface. This pressure is the main driving force for its work. Only when it can withstand these strong pressures can it be used for construction ; 3. This machine is made of high-quality steel, which has good resistance both in hardness and wear resistance, which is reflected in a long service life in use; 4. The cutting of this machine is smooth, the powerful laser processing is very fast, and the processing effect is also very good. Higher quality of flatness and levelness – the ground elevation can reach laser-level precision, the ground flatness and levelness are 2-3 times that of manual leveling, the concrete density is increased by more than 20%, and it is suitable for dry hard concrete , Fiber concrete and large aggregate concrete. Reduce the sub-bin seam, can achieve no sub-bin seam construction. Due to maintenance and formwork support, the sub-storage joints on the large-area concrete floor will have defects such as damage along the joints. These problems can be avoided by using laser leveling and joint cutting technology. The construction speed is faster – the work efficiency is increased by 100-300% (100-200 square meters of paving work can be completed per hour, and an average of 2000-3000 square meters can be completed per day), and labor is reduced by more than 30%, which is especially suitable for the construction period requirements Projects with compact size, large paving area and high quality requirements. Better ground integrity – it is very easy to achieve large-area overall pouring. On the one hand, this overall pouring technology can avoid problems such as easy hollowing and cracking caused by floor layered pouring, and on the other hand, it can reduce a lot of Construction joints make the integrity of the ground better. This is not easy to do with other construction techniques. It can reduce the post-maintenance cost of the ground – because the large-area overall paving can reduce the construction joints by more than 3 times – and the construction joints are easily damaged by the wheel load, thus reducing the post-maintenance cost of the ground. Long-term cooperation with supporting manufacturers has gone through a complete production process of R&D, manufacturing, and testing. It has the characteristics of high rigidity, high precision, high efficiency, and durability. It is mainly made of high-quality cast steel and is a product trusted by small and medium-sized enterprises. Adhering to the belief of "quality, reputation and service first", the company's VANSE laser leveling machine will be delivered in time within the time negotiated by both parties after confirming the customer's order. With strong technical strength, advanced and sophisticated processing equipment and strict Excellent management effectively guarantees the high quality and timely delivery of VANSE Laser Leveler.

The development of concrete laser leveling machine is the need of the times! The concrete laser leveling machine adopts the principle of laser leveling, which is more scientific and accurate than the traditional manual measurement method, and greatly reduces the error value caused by manual measurement. For some environments that require ultra-flat ground Said that this way of working is more acceptable and more in line with the needs of users. (1) The leveling principle of the laser leveling machine is realized under the automatic control of the computer by using precision laser technology, closed-loop control technology and highly precise hydraulic system. This is the most prominent difference between it and other floor construction processes. specialty. (2) The leveling principle of the precision laser leveling machine is to rely on the leveling head driven by hydraulic power, cooperate with the laser system and the computer control system to complete the leveling work while automatically leveling. The leveling head is equipped with an integrated scraper, vibrator and leveling plate, which integrates all leveling, leveling, vibration and compaction work, and completes it at one time. The computer control system automatically adjusts the elevation 10 times per second in real time, and the vibration frequency of the vibrator with a balanced design reaches 3000 times per minute. (3) The laser transmitter used to control the ground level is arranged independently, so that the level of the ground is not controlled by the template, and no cumulative error will occur. The original traditional labor-intensive operation methods no longer meet the needs of development. The integration of machinery and equipment and intelligence must have become the mainstream of the times. The current construction industry has already adopted laser leveling machines to replace the traditional ground paving mode. Rapid paving of large areas can ensure the quality of construction. The ground paved by this equipment is more flat and compact, so that the flatness of the ground is guaranteed. The laser leveling machine has a high leveling ground, which significantly improves the flatness of the ground. The ground constructed by the laser leveling machine and the traditional method are tested at 22 points (one point every 5mx4m), and the average flatness is 1.3mm and 4.1mm respectively. The leveling quality of the laser leveling machine can be improved by more than 3 times compared with the traditional method. Reduce the amount of side formwork dismantling: Based on the statistics of 20,000 square meters of concrete pavement, the traditional method needs to dismantle 5800m of side formwork, but with advanced equipment such as laser leveling machines, the dismantling of 2500m can reduce the support modulus by more than 74%. Fast construction speed: use laser leveling machine and other equipment to construct large slabs, which improves the work efficiency by 3 times compared with the traditional beam vibrator method, saves 30%, and can complete 3000 square meters per day on average, especially suitable for large-scale concrete surface construction. High degree of automation and low labor intensity: the use of laser leveling machine equipment can change the heavy manual labor into mechanical paving, vibrating, leveling, pulp extraction, and surface plastering, reducing the number of operators by 30% and reducing labor intensity. The application of equipment such as laser leveling machines can realize large-scale construction, effectively reduce a large number of construction joints, and the concrete slump can also be significantly reduced. The concrete strength is guaranteed, so that the ground integrity is good and cracks are not easy to appear. High economic benefit, the use of laser leveling machine can save 2-3 yuan per square meter compared with the traditional process, less seams, and lower maintenance costs in the later period, so that the economic benefit can be significantly improved.

Tell you how effective the concrete laser leveling machine is! Many consumers are still hesitating whether they should buy a concrete laser leveling machine, because they have no concept of the construction effect of the equipment. Today we will introduce the use effect of the equipment. First of all, the biggest feature of this equipment is that it is fast, and the time-consuming is 1/10 of manual work, which is enough to make many construction teams excited; secondly, it is flat, and the ground level error after paving is small , is almost negligible. 1. Requirements for concrete and formwork ① Concrete: Concrete must be produced, conveyed or pumped to the flooring site by a commercial concrete production plant. ② Concrete specifications: C25~C30 concrete, the strength of which is not less than 25MPa in 28 days, according to the design requirements. ③ Water-cement ratio: N o more than 0.5, no water can be added during the feeding process. ④ Cement: Use ordinary Portland cement with a grade of not less than 42.5. ⑤ Aggregate: Well-graded aggregate should be used. Crushed granite or pebbles are used as coarse aggregate, and the maximum diameter is not more than 25mm. The fine aggregate is clean river sand with a fineness modulus of 2.4-2.7. ⑥ Concrete mix ratio: The amount of cement is not less than 350Kg/m3. In order to avoid surface quality problems, the sand rate should be controlled at 35% to 40%. ⑦ Concrete slump: 14±2cm, maximum 16cm. ⑧ Setting time: The initial setting time should be controlled within 3-5 hours. In order to avoid the excessive deviation of the surface elevation affecting the joints, the formwork should be steel formwork. The height of the formwork should be controlled within +0 and -2mm, and the steel formwork should be within 1-1.2 meters from the surrounding walls. 2. Construction cooperation requirements ① The concrete feeding speed should be determined according to the ground thickness and pouring area to determine the minimum hourly feeding speed. For a floor with a thickness of 200 mm, if the width of one-time pouring reaches 40 meters, the minimum feeding speed should reach 40 cubic meters per hour, otherwise there will be cold joint problems, which will affect the quality of ground construction. ② Manually coordinate the concrete sent to the platform, and workers need to remove it as soon as possible and roughly level it. In addition, the areas around the formwork, walls, columns, trenches, equipment foundations, floor drains or around pipelines that cannot be leveled require manual cooperation for local leveling. Generally, 3-4 workers are required to cooperate with the construction (provided by Party A). ③ Other precautions In order to ensure the flatness of the ground, attention should be paid to: 1) The slump of concrete sent to the platform must be consistent each time. 2) Ensure that the concrete feeding speed reaches 40 cubic meters per hour or above, and the initial setting time of each batch of concrete must be consistent. 3) Ensure that the formwork elevation is accurate and cannot be disturbed during construction. 4) Environmental cooperation. The concrete floor that has just been constructed cannot be exposed to sunlight, wind, rain, etc. that are unfavorable to concrete health. ④ Other requirements: A. In order to avoid random cracks in the floor, the cutting time of shrinkage joints should be carried out as early as possible (within 24 hours). B. At the same time as the construction of the laser leveling machine, there should be no electric welding machines on site, and no reflective objects (such as glass windows). C. The foundation must reach a certain hardness to ensure that the laser leveling machine does not collapse when working on the ground. D. The height of the ground in the factory building shall be calibrated by Party A, and the points must be evenly distributed, and there must be no error in the levelness. E. Pouring concrete must be operated according to the requirements of Party B's technicians.

VANSE leveling machine speaks with quality and service! The laser transmitter of the concrete laser leveling machine generates a rotating laser. The laser receiver on the laser leveling machine receives the signal and is analyzed by the laser measurement and control system. The deviation will be fed back to the sensitive computer control system on the laser leveling machine. The linear actuator will adjust the height of the scraper to ensure leveling accuracy. Shandong VANSE Machinery, as the earliest and most professional manufacturer of laser leveling machines in China, believes that occasional quality problems are not enough to negate the strength of the entire brand. Does a brand have strength? The key lies in whether the company has a sound after-sales system and whether it can provide high-quality after-sales service in the first place. High-quality products are the theme of long-term development of enterprises, and high-quality services are the key to the sublimation of corporate brand image. Shandong VANSE laser leveling machine manufacturer has been committed to the research and development and production of concrete laser leveling machine products for many years. The product quality has also experienced the test of various working conditions, and the high-quality after-sales service has been recognized by the majority of users. Our service tenet As long as there is a VANSE laser leveling machine, we only need a call from you, and we can always provide you with high-quality services in the first time. We insist on making high-quality products and high-quality services!

Due to the limitation of construction technology, the road surface is uneven in many cases, and the vehicle cannot maintain a very good stability during driving, and it may cause ruts after repeated rolling, which is equivalent to being stuck in a car. vicious circle. Wouldn't it be better to use concrete laser leveling? Nowadays, many roads are uneven, and there are many reasons. Now I will introduce the reasons for uneven roads: 1. The unevenness of the base layer affects the flatness of the road surface, resulting in uneven paving thickness, and the control of the base layer construction is not strict. Some even use bulldozers and graders to lay the base layer. The construction quality and flatness are difficult to control. 2. The influence of road paving machinery and technology on the smoothness: A. Improper selection of paver structure parameters, resulting in uneven paving thickness and waves; B. Improper control of the base line of the paver, resulting in waves; C. Improper operation of the paver causes uneven paving speed and frequent starting, resulting in rough and uneven surface layers; D. When a slipform paver is used for the concrete pavement, it is affected by the paver itself, control datum line and operation. 3. The influence of the quality of surface paving materials on the flatness: A. The ratio of asphalt pavement materials, mixing, oil temperature and shutdown due to material failure; B. Raw materials, proportioning and stoppage of materials for concrete pavement. 4. Effect of rolling on flatness: A. The use of low-frequency, high-amplitude road rollers will cause jumping and tamping phenomena, and excessive initial tonnage will cause pushing deformation; B. Uneven rolling speed, sudden braking, sudden start, random parking and U-turn, parking on the rolled and formed road without turning off the vibration device will cause road congestion, and stopping on the uncooled road will cause sunken; C. Improper rolling route, if you don’t pay attention to wrong wheel rolling, turning back at the same cross section every time will cause uneven road surface; D. The number of times of rolling is not enough, the compaction is not enough, and ruts are easy to form after opening to traffic. The leveling mechanism of the laser leveling machine is driven by hydraulic pressure, cooperates with the laser system and the computer control system to complete the leveling work while automatically leveling, and the work efficiency is extremely high. The laser transmitter used to control the ground level is arranged independently, and the level of the ground will not produce cumulative errors. Compared with the traditional method, the flatness of the super-large area is as easy to control, and at the same time, the construction joints and formwork usage of the floor are greatly reduced. Fast construction speed: use laser leveling machine and other equipment to construct concrete slabs, which improves the work efficiency by 3 times and saves 30% compared with the traditional beam vibrator method. It can complete 2000 square meters per day on average. It is especially suitable for simple shapes and large-scale operations. pavement construction. High degree of automation and low labor intensity: the use of laser leveling machines and other equipment changes heavy manual labor into mechanical paving, vibrating, leveling, slurry extraction, and surface plastering, reducing the number of operators by 30% and reducing labor intensity at the same time. High economic benefit: the application of laser leveling machine and other equipment saves the cost by 2-3 yuan/㎡ compared with the traditional process, with fewer joints and lower maintenance costs in the later period, so that the economic benefit is significantly improved. Advanced equipment such as laser leveling machines are especially suitable for projects such as docks, storage yards, expressways, airports, large squares, parking lots, and municipal roads that have relatively simple shapes, large amounts of action, and high construction quality requirements.

HOW TO MAINTAIN CONCRETE FLOORS IN DIFFERENT SEASONS? -VANSE Machinery The current concrete floor is compacted with a concrete laser leveling machine, and there is almost no error. Concrete technology is becoming more and more important. Concrete has developed from the initial low-strength grade and ordinary concrete to today's high-strength grade and high performance. Sometimes the maintenance of concrete is often ignored in engineering construction, causing the surface of the concrete to shrink. , cracking, peeling and other phenomena, in order to make the concrete floor more sustainable and long-term use, it is necessary to pay special attention to the concrete curing method during construction. Different environments have different maintenance methods: During the high temperature and dry season, the moisture in concrete is easy to lose, so the following measures should be actively taken: 1. Cooling measures must be taken during construction, such as choosing to pour at night to avoid direct sunlight, and adjusting the concrete ratio in time. 2. At the same time, it must be noted that the temperature of the concrete formwork must be cooled, because if the temperature of the formwork is too high, the surface of the concrete will lose moisture quickly after pouring, resulting in defects such as sanding on the concrete surface. The maintenance of concrete in this season requires a lot of water, especially for the parts that are not easy to maintain, such as columns, cover beams, and beam webs, they should be tightly wrapped with geotextiles and sprinkled regularly. The surface of the concrete is always in a humid environment. In the early stage of curing, the concrete surface is sometimes dry and sometimes wet, because the strength of concrete that is sometimes dry and sometimes wet is easy to reduce, and it is easy to produce shrinkage cracks. Therefore, within 7 days of concrete pouring, it is necessary to prevent water evaporation and keep the concrete surface moist. In short, the focus of concrete maintenance in this season is moisturizing. If measures such as moisturizing and cooling are done well, problems such as early setting of concrete, plastic cracks, reduction of concrete strength and durability caused by high temperature will not appear. In the cold season when the temperature is lower than 5°C, the following measures should be taken for the maintenance of concrete: 1. After demoulding, cover and maintain the insulation. 2. The use of steam curing. 3. Improve the thermal insulation performance of the formwork. Most of the steel formwork used in bridge construction has good thermal conductivity and is easy to lose temperature. Therefore, insulation materials such as straw curtains should be wrapped outside the formwork or measures such as thickened formwork and double-layer formwork should be used. 4. Increase the mixing temperature of concrete. First of all, the heating treatment of the mixing water can be considered, and the aggregate can also be considered to be heated. The purpose is to ensure the initial cement hydration temperature and improve the early strength of the concrete. If the maintenance of concrete in the early cold period takes the above measures actively, the concrete will be prevented from freezing due to low temperature. After the concrete is frozen, its hydration will stop. After the temperature rises, although it can continue, the surface of the concrete has changed. Crisp, lose strength, and even larger cracks appear. Therefore, it is necessary to especially strengthen the early insulation and maintenance of concrete, and it must not be frozen before the concrete strength reaches 50% of the design strength.

Engineers provide door-to-door service to customers in time. The Large laser leveling machine is a high-precision, high-efficiency measuring instrument, which uses laser beam technology for measurement, and has the advantages of fast, accurate, and high degree of automation. It is mainly used for level control in civil engineering, which can measure the difference in ground height and provide an accurate level reference for building construction. Compared with the traditional level, t he Large las er leveling machine has greatly improved the measurement speed and accuracy. The Large laser leveling machine has a wide range of measurement and can be used to measure the level of various places such as roads, bridges, tunnels, airport runways, expressways, and large warehouses. It can quickly measure the difference in ground height, and automatically process the data, and finally output accurate horizontal data. In construction projects, Large laser leveling machines can improve construction speed and quality, reduce construction costs and waste of human resources, and can also improve project reliability and safety. The operation of the large laser leveling machine is very simple and only needs one person to complete it. It uses laser beam technology for measurement, real-time display of measurement results and automatic data processing. At the same time, it can also be set according to actual needs, including parameters such as measurement range and accuracy. During use, you only need to place the Large l aser leveler at the measurement position, turn on the switch, and adjust the appropriate height to start the measurement. The entire measurement process is very simple and does not require additional manpower and time costs. To sum up, the large laser leveling machine is a very practical measuring instrument with the advantages of high precision, high efficiency and high degree of automation. It can be widely used in level control in civil engineering, providing accurate level reference for building construction. In the future, with the continuous development of science and technology, Large laser leveling machines will be more intelligent and convenient, providing more accurate and efficient services for construction.

Laser leveling machines are widely used in modern industrial plants, large shopping places, warehouses and other large-area concrete ground construction. Its maintenance can greatly improve the life of the machine and save costs. Laser leveling machine maintenance method/step Fuselage cleaning: When cleaning the surface of the machine, first check whether there is any depression or leakage in the fuel tank, oil pipes, joints, etc., and check whether the fixing screws of the fuel tank bracket are tightened before cleaning. Prevent rust: In the daily maintenance of the laser leveling machine, butter or anti-rust oil should be used to prevent the rust of the exposed parts and mechanical parts, and the gears, sprockets and other parts should be lubricated every half a month. Leveling: The quality of the leveling and the construction quality also have a necessary relationship. Some buildings have a lot of dust or other sundries, which will cause the leveling machine to level the concrete and become dirty, which will lead to unqualified construction. Therefore, it is usually necessary to Remember to tell Xun Phi to clean the leveling in time. Oil replacement: The engine oil and hydraulic oil in the machine need to be replaced after a period of use. Most people think that it is enough to drain the oil in the oil tank and fill up with new hydraulic oil. But at this time, there will be a lot of old grease trace hydraulic oil in the hydraulic oil pipe. When the equipment is in use, the new oil and the old oil will be mixed together, which will shorten the service life of the new oil. The correct oil change procedure is to drain the hydraulic oil in the hydraulic oil tank first, clean the oil tank and then add new hydraulic oil. Then remove the circuit main pipe, start the engine and run it at a low speed to make the oil pump work, operate each mechanism separately, and use new hydraulic oil to discharge the old oil in the circuit one by one until new oil flows out of the oil return main pipe. Finally, connect the oil return main pipe to the fuel tank, and add new hydraulic oil to the fuel tank to the specified position. Precautions The usual maintenance and maintenance of machinery is important, but it is more important to choose a good machine equipment. VANSE laser leveling machine is your best choice!