In what scenarios might a concrete laser leveling be more suitable?

  With the development of science and technology, laser leveling machines have become essential equipment for the construction industry such as road leveling. The equipment has high work efficiency and simple operation and is favored by users. However, for novices who do not often deal with the machinery industry, they do not know much about the use process and methods of laser leveling machines. Because of this, they often encounter problems during use. If you want to know how to use it specifically, don't miss the wonderful content below. After the base is processed, debug the laser leveling machine, and make a fixed reference leveling point based on the original leveling point; lay non-woven fabrics, support side molds, set up laser transmitters, and introduce the ground elevation into the laser leveling machine according to the original leveling point. Commercial concrete is used. Tankers transport commercial concrete to the entrance and exit of the car warehouse, and then transport it to the construction site with a three-wheel dump truck. Use a handheld laser receiver to check the floor elevation, introduce the elevation into the laser leveling machine, and adjust the reference point on the laser leveling machine. (1) After the formwork is set up, before pouring concrete, the warehouse should be cleaned and rinsed with water one day in advance. When pouring, drain the open water and sweep the cement slurry or interface agent. At this time, it is strictly forbidden to have obvious water accumulation. If there is, it must be removed resolutely before paving concrete. (2) After the concrete is put down, it should be initially flattened. The flattening height should be 3 cm higher than the elevation. Then use a laser leveling machine to level it. For corners that cannot be leveled, you can use a gasoline leveling ruler or manual scraping. (3) When pouring the warehouse near the wall, wait until the laser leveling machine passes by, and then use a scraper to level it in time. And so on. (4) When pouring the warehouse near the wall, wait until the laser leveling machine passes by, and then use a scraper to level it in time. And so on. For areas where concrete mixer trucks cannot be driven to the site, tractors should be used to transport concrete. After pouring, wait for the concrete to initially set before starting floor finishing construction. During the construction, the operator uses a handheld laser receiver to detect the ground after the machine is installed, and once again ensures that the flatness error is within the controllable range. In order to facilitate everyone to better understand and master, this article only briefly discusses the operation process of the laser leveling machine. Later, we will continue to explain other related content about the leveling machine. Interested friends can visit our official website at any time to inquire for more information.

  As we all know, the service life of the laser leveler is limited. If you don't want the life of the leveler to end early, you need to follow the rules during use. As an expert in the production and use of levelers, laser levelers naturally have a lot of knowledge that others don't know. In order to help users learn to use the leveler, laser levelers will give a detailed introduction in today's content, so please don't miss it. ▲ After the laser leveler manufacturer completes the leveling operation, it will perform routine maintenance operations in accordance with the contents of the routine maintenance procedures. ▲ The working devices and motion mechanisms of the leveler that are in direct contact with the asphalt mixture during the operation are sprayed with diesel after the operation and then run for a period of time to remove the residual asphalt on them, so that they can operate freely and rotate flexibly. It is forbidden to spray diesel on the electronic control system and spiral wire to prevent fire and burning when the power is turned on. ▲ After leveling the fly ash soil operation, flush with water to flush away the white material. After flushing, use waste hydraulic oil to lubricate the active parts of the scraper conveyor chain, and apply anti-rust oil to the piston rod. Be careful not to flush the electrical appliances and bearings with water to prevent short circuits and foreign objects from entering the bearings. ▲ Clean and check the vertical slope meter lifting and adjustment device, and apply grease to the screw. Apply grease to the floating arm slide rail. Grease each oil filling point until the joints overflow. For leveling machines with oil filling cups, observe the consumption and fill them up at any time. ▲ Due to the high efficiency of construction, the later seam cutting needs to keep up. Generally, each laser paving leveling machine is equipped with 7-8 seam cutting machines to meet the requirements. ▲ The speed of the laser leveling machine should not be too fast during the leveling operation; ▲ The laser leveling machine manufacturer should perform initial leveling before concrete leveling, and the concrete after initial leveling should be higher than the established elevation. ▲ It is advisable to use ground film covering maintenance in the early stage, and cover the non-woven fabric after cutting the seam. ▲ When installing the laser transmitter, be careful to avoid obstacles; ▲ During the construction process, due to the side pressure of concrete, the steel mesh is easy to move horizontally. For this reason, an isolation bench is directly placed on the adjacent steel mesh, and the horizontal movement of the steel mesh is effectively controlled, and the bench can be used in rotation. The above is the relevant matters that our concrete laser leveling machine manufacturer tells you. I hope it can help you. If you want to buy it, please contact us as soon as possible. The contact number and company address of our company are at the bottom of the screen. Whether you call for details or come to the factory for inspection, we warmly welcome you.

  – Site size – For large-scale concrete construction sites, such as large industrial plants, warehouses, parking lots, etc., it is recommended to choose a ride-on trowel. The ride-on trowel has high working efficiency and can complete large-scale troweling work in a short time. For example, for the floor construction of a logistics warehouse with an area of ​​more than 1,000 square meters, a ride-on trowel can quickly perform rough and fine grinding, effectively saving time and manpower. – For small-area indoor floors or local repair work, a walk-behind or handheld trowel is more suitable. For scenes such as home indoor floor decoration and small store floor repair, the walk-behind trowel is flexible to operate and can easily operate in narrow spaces and corners. – Ground flatness requirements – If the flatness and finish of the ground are extremely high, such as the floor of a high-end shopping mall, the clean workshop of an electronics factory, etc., a double-disc trowel needs to be considered. The double-disc trowel can better ensure the flatness of the ground. Its two trowel discs work at the same time, which can reduce the height difference of the ground and make the ground achieve a mirror-like effect. – For general ground, such as outdoor roads in ordinary houses, simple activity venues, etc., a single-disc trowel can meet basic troweling needs. – Electric trowel – Advantages: The electric trowel has the characteristics of low noise and no pollution, which is suitable for use indoors or in places with high requirements for environmental noise. Moreover, the operation of the electric trowel is relatively simple, and it is convenient to start and stop. You only need to turn on or off the power. – Disadvantages: The working range of the electric trowel is limited by the length of the power cord. If the construction site is large, the socket position may need to be changed frequently. In addition, the power of the electric trowel is relatively weak. When facing thicker or harder concrete, it may be insufficient. – Gasoline trowel – Advantages: The gasoline trowel has strong power, is suitable for various types of concrete, is not limited by the site power supply, and has good maneuverability. It can be freely moved and operated in remote construction sites or large open-air sites without power supply. – Disadvantages: Gasoline trowels are noisy and produce exhaust emissions, which have a certain impact on the environment and the health of operators. In addition, its maintenance cost is relatively high, and parts such as engine oil and spark plugs need to be replaced regularly. – Size of trowel disc – The larger the size of the trowel disc, the larger the coverage area of ​​a single trowel and the higher the work efficiency. Generally, the diameter of the trowel disc of a hand-held trowel is between 600 and 1000 mm, and the diameter of the trowel disc of a ride-on trowel may reach more than 1000 mm. When choosing, determine the appropriate trowel disc size based on the size of the construction site and actual needs. – Speed ​​range – The appropriate speed is one of the key factors to ensure the quality of troweling. Too high a speed may cause the trowel disc to wear too quickly and cause defects such as wavy lines on the ground; too low a speed will affect the troweling efficiency. The speed of a general trowel is between 70 and 150 rpm. The speed range of trowels of different brands and models may vary, and needs to be selected according to specific construction requirements. – Power – The power determines the working capacity of the trowel. For large trowels or when thicker and harder concrete needs to be processed, higher power is required. For example, the power of a ride-on trowel is generally between 5 and 10 horsepower, the power of a walk-behind trowel is usually between 3 and 5 horsepower, and the power of a handheld trowel is relatively low, generally between 1 and 3 horsepower. – The consumable parts of a trowel mainly include trowel blades, bearings, drive belts, etc. When purchasing a trowel, consider whether these consumable parts are in sufficient supply and whether they are easy to purchase. For example, some niche brands of trowels may have consumable parts that are difficult to find, making repair and replacement inconvenient. At the same time, you should also compare the prices of consumable parts of different brands and models of trowel machines, and try to choose a trowel machine with lower consumable parts costs, so as to reduce the cost of later use and maintenance. – Brand reputation: Choosing a trowel machine from a well-known brand can usually guarantee the quality and performance of the product. Well-known brands have stricter standards in product research and development, production processes, quality control, etc., and their products are more reliable. For example, some brands with many years of production experience in the field of construction machinery have had long-term inspections on the market and received good user feedback. – After-sales service: Good after-sales service is an important factor in ensuring the normal use of the trowel machine. After-sales service includes product warranty period, timeliness and professionalism of maintenance services, technical support, etc. When purchasing, you should understand whether the manufacturer provides door-to-door maintenance services, the speed of supply of maintenance parts, and whether there is a professional customer service team to answer questions encountered by users during use.