Welfare! Four steps to clean the laser leveler

Finishing concrete is not an easy job. During construction, workers' hands, backs and knees are vulnerable to injury. The advent of the trowel allows construction workers to stand while the concrete is finished. Based on the size of the project, the number of people and the customer's requirements for the surface layer, the construction party may consider purchasing a trowel. If you are a construction party specializing in concrete staining, staining or home improvement polishing, maybe you don't need to buy a ride-on trowel (double disc machine). This type of troweling machine is not only expensive, but also has a high hardness of the ground after finishing, so the above-mentioned type of ground does not have such high requirements. In fact, a walk-behind trowel is sufficient to meet the work requirements of pulping and finishing small-area floors. Under what circumstances should you consider investing in a trowel? In general, construction area is an important consideration. "Even a small-area project can use a trowel, even if the project is only a few hundred square meters. As long as the construction area reaches 100 square meters, you must use a trowel, and if it exceeds 300 square meters, you have to consider using a small ride-on trowel From another perspective, the work efficiency of a single-disk trowel is equivalent to that of three construction workers using traditional manual finishing tools such as scrapers. It seems that the biggest advantage of the trowel is to increase the speed of application. But this is only a one-sided understanding of the advantages of the trowel. What the trowel gives is not a simple speed increase but the efficiency when dealing with large-scale construction. Furthermore, the troweling machine allows the construction party to choose a more appropriate time to start the machine when dealing with large-scale construction, instead of having to start early due to the need to consider the overall area of construction like traditional construction. Troweling machine operation steps: 1. Before use, check whether the motor, electrical switch, cable and wiring are normal and comply with the regulations, and install a leakage protector. 2. Before use, check and clean up the sundries on the wipe plate to avoid the whole machine from jumping when in use. 3. After turning on the power, carry out a test run, the blades will rotate clockwise and must not be reversed. 4. Operators should wear insulating shoes and gloves, and the cables should be picked up by auxiliary personnel, who should also wear insulating shoes and gloves. Pay attention to prevent electric shock accidents caused by the cable insulation layer being broken. 5. The troweling machine breaks down, and it needs to be shut down to cut off the power before it can be repaired. 6. The trowel should be stored in a dry, clean and non-corrosive gas environment. The handle should be placed in the specified position, and no rough loading and unloading should be allowed during transfer. Construction Notes: 1. During construction, pay attention to the temperature of the motor reducer box not exceeding 80° 2. The engine oil in the turbine box needs to be checked frequently. If the oil level is lower than the oil level, please refuel in time. After each use, the equipment should be cleaned in time, especially the smears should be stored in a dry, clean and non-corrosive environment. When the smear is worn to 30mm on one side, loosen the nut, turn the smear around and re-tighten the screw to achieve the purpose of two pairs of use. Angle of smear Rotate the hand wheel to adjust the angle of smear to achieve the ideal effect of rough smearing. If you need to shut down during construction, please turn off the power in time. When the gasoline engine stops, press the switch on the handle in time to stop. The ground effect after the troweling machine is more uniform, the construction speed is faster, and the operation is more convenient. Working with a hand-held spatula for a long time will easily fatigue the knees, shoulders and elbows of the construction workers, which will affect the construction effect. To put it simply, the use of a trowel makes the difficult operation easier, and it is the best equipment for finishing the floor.

– Troweling machine: Mechanized operation, fast construction speed, can quickly complete large-area concrete surface troweling work. – Manual troweling: Depends on manual operation, slow speed, low efficiency, and takes a long time for large-area construction. – Troweling machine: Can provide a more uniform and smoother surface, reducing errors caused by human factors. – Manual troweling: The quality is greatly affected by the skills and experience of workers, and there may be differences in flatness and uniformity. – Troweling machine: Reduces manual labor, reduces labor intensity, and reduces the physical burden of workers. – Manual troweling: The labor intensity is high, and workers need to bend over for a long time, which is easy to cause fatigue and occupational diseases. – Troweling machine: The initial investment is high, but in the long run, due to high efficiency and high-quality construction, the overall cost can be reduced. – Manual troweling: The initial cost is low, but the labor cost is high, and inconsistent construction quality may lead to increased maintenance costs in the later stage. – Troweling machine: Reduces the risk of workers directly contacting wet concrete and improves construction safety. – Manual troweling: Workers need to work on slippery concrete surfaces, which may cause slips and injuries. – Troweling machine: Can work in a variety of environmental conditions, including bad weather, but may require additional maintenance and care. – Manual troweling: Affected by environmental conditions, such as high temperature, rain and snow, which will seriously affect the progress and quality of construction. – Troweling machine: Operators need to master certain mechanical operation skills and safety regulations. – Manual troweling: Relies on the workers' manual skills and experience, and has high technical requirements. – Troweling machine: Mechanized operations reduce dependence on human resources and are in line with the sustainable development trend of the modern construction industry. – Manual troweling: labor-intensive operation, with rising labor costs, less sustainable. In summary, concrete trowels have obvious advantages in efficiency, quality, safety and sustainability, while traditional manual troweling has certain advantages in flexibility and initial cost. With the development of technology and the rise in labor costs, mechanized construction has gradually become the mainstream.

  In the hot summer, the construction of concrete laser leveling machines has not stopped. The high temperature construction environment in summer is a heavy test for engineering machinery and equipment such as concrete laser leveling machines. Therefore, it is very important to do a good job of daily maintenance of laser leveling machines in summer. Today, the editor of Shandong Vanse will explain to you some construction precautions for concrete laser leveling machines in summer for your reference. 1. In summer construction, we must first prevent the engine from overheating. Under normal circumstances, the engine temperature should not exceed 95°. If the temperature is too high, we should choose a relatively cool area to shut down and cool down. At the same time, we can lift the engine hood for ventilation and heat dissipation. 2. The amount of cooling water should be detected in time. When the water radiator reaches 100°, do not rush to add cooling water. Instead, we should shut down the engine immediately to cool down the engine at idle speed, and then add coolant. 3. The construction temperature in summer is high. We should check the tire pressure and tire temperature frequently. If the tire temperature is too high, we should shut down the engine in time and place it in a cool place to cool down. Remember to use the wrong method of deflation or pouring cold water to cool down. 4. Check the battery level frequently, add distilled water in time, dredge the vents, pay attention to the density of the electrolyte, and maintain a good charging state. 5. Prevent engine explosion. Before entering the summer, the carbon deposits in the combustion chamber, valve top and other parts should be thoroughly removed to maintain good heat dissipation and normal compression ratio; and the fuel supply advance angle should be checked and adjusted to prevent engine explosion. 6. Check the temperature of hydraulic oil and hydraulic transmission oil frequently. If the temperature is too high, stop the machine for a rest, and never exceed high temperature operation. In short, engineering machinery such as concrete laser leveling machines are subjected to the test of long-term continuous operation during summer construction, and are also affected by high temperature environments. Therefore, summer construction must pay attention to the above conditions, and regular inspections and maintenance work must be carried out regularly, which is not only related to the service life of the concrete machine leveling machine, but also to the construction hidden dangers and the smoothness of the concrete laser leveling machine at work.