Technical Knowledge
What special attention should be paid to the maintenance and care of concrete laser leveling machines under different climatic conditions?
1. Under high temperature climate conditions
– Cooling system maintenance:
– Under high temperature environment, the engine (if it is a fuel laser leveler) and hydraulic system are prone to overheating. For the engine, make sure that the coolant in the radiator is sufficient and clean. The coolant level should be checked regularly, generally every 8-10 hours of work, and the coolant should be replaced regularly according to the requirements of the equipment manual. It is usually recommended to replace it once a year.
– Clean the dust and debris on the surface of the radiator, as these will affect the heat dissipation effect. You can use a compressed air can or a soft brush to gently clean it to avoid damaging the radiator fins.
– For the hydraulic system, some laser levelers are equipped with a hydraulic oil cooler. Also ensure that its surface is clean and pay attention to the temperature of the hydraulic oil. If the hydraulic oil temperature is too high, it may cause the performance of the hydraulic system to decline or even damage.
– Equipment working time adjustment:
– Try to avoid using the equipment for a long time when the temperature is highest during the day (usually 12 noon-3 pm). Because during the high temperature period, the operating temperature of each component of the equipment is already high, and long-term continuous operation will further aggravate heat accumulation and increase the risk of equipment failure.
– The working time can be adjusted to the early morning or evening, when the ambient temperature is relatively low, which is conducive to the normal operation of the equipment. If it is unavoidable to work during high temperature periods, the rest frequency of the equipment should be increased. After every 1-2 hours of work, the equipment should be allowed to rest for 15-20 minutes to allow the various parts of the equipment to fully dissipate heat.
– Lubrication and seal inspection:
– High temperature will accelerate the evaporation and aging of lubricating oil (grease), so the lubrication of the equipment should be checked more frequently. For example, for the bearings, chains and other parts of the equipment, lubrication may be performed once every 50-100 hours of work. In a high temperature environment, it is necessary to check and add grease every 30-50 hours of work.
– At the same time, check the seals of the equipment, such as the seals at the joints of the hydraulic pipes and the engine oil seals. High temperature may cause the seals to age and deform, resulting in leakage. If the seals show signs of damage, they should be replaced in time to avoid leakage of hydraulic oil or coolant, which will affect the normal operation of the equipment.
2. Under low temperature climate conditions
– Fuel and battery management:
– For fuel-type laser levelers, use fuel suitable for low temperature environments. In cold weather, diesel may wax, which will affect the start and normal operation of the engine. You can add anticoagulants or use low-grade winter diesel to solve this problem.
– Battery performance will decrease at low temperatures, so make sure the battery is fully charged. When the equipment is not in use, the battery can be removed and placed in a warm room for charging and storage. In addition, before starting the equipment, the battery can be preheated, such as using a battery heater, which can improve the battery's starting ability.
– Preheating before starting:
– The engine should be fully preheated before starting. According to the requirements of the equipment manual, use a preheating device to preheat the engine. The preheating time is generally determined by the ambient temperature. For example, in an environment of about minus 10℃, the preheating time may take 10-15 minutes.
– For the hydraulic system and working parts, do not let the equipment work at full load immediately after starting. Let the equipment run at no load for 5-10 minutes to gradually heat up the hydraulic oil and various components. After reaching the normal working temperature, start construction.
– Precautions for equipment storage:
– If the equipment is not used for a long time, it should be stored indoors or in a place with insulation measures to avoid exposure to cold outdoor environments. If it can only be stored outdoors, the equipment should be properly covered to prevent damage to the equipment caused by snow and ice.
– Antifreeze can be added to the water tank and hydraulic oil tank of the equipment to prevent the water tank and oil tank from freezing and cracking at low temperatures. The amount of antifreeze added should be in accordance with the requirements of the equipment manual. Generally, the concentration of antifreeze should be ensured to effectively prevent freezing at the expected minimum temperature.
3. Under humid climate conditions
– Waterproof and moisture-proof measures:
– Check the electrical system of the equipment to ensure that all electrical components (such as motors, controllers, sensors, etc.) have good waterproof seals. For wire connectors exposed to the outside, waterproof tape or sealant can be used to wrap them to prevent moisture from entering and causing short circuits.
– The laser transmitter and receiver of the laser leveling machine should also be waterproof. In humid weather, if these precision components are damp, it may affect the transmission and reception of laser signals, thereby affecting the construction accuracy. You can use a special waterproof cover to protect it. When the equipment is not in use, store these parts in a dry place.
– Rust-proof treatment:
– Humid air can easily cause equipment to rust, especially the metal parts of the equipment. Anti-rust oil or anti-rust paint can be applied to the surface of the equipment, and the parts that are prone to rust (such as chassis, scrapers, screws, etc.) should be protected.
– Regularly check whether the equipment has signs of rust. For rusted parts, rust removal should be carried out in time. You can use sandpaper or rust remover to remove the rust, and then apply anti-rust oil or touch-up paint.
– Post-work drying treatment:
– After working in humid weather, the equipment should be cleaned and dried in time. Use a clean rag to wipe off the moisture on the surface of the equipment. For parts inside the equipment that may be damp (such as the cab, electrical control cabinet, etc.), a hair dryer or dehumidifier can be used to dry them.
– At the same time, the working parts of the equipment (such as scrapers, spiral distributors, etc.) should be cleaned to prevent concrete residues and moisture from mixing and solidifying on the parts, affecting the next use of the equipment.
Thanks to All the Friends Who Support and Trust Shandong Vanse Machinery Technology Co., Ltd.
If you want to know more about Shandong Vanse Machinery Technology Co., Ltd. or have any questions, please feel free to contact us:
Our Factory
Shandong Vanse Machinery Technology Co., Ltd.
Share this article
About the Author: Shandong Vanse Machinery Technology Co., Ltd.
Shandong Vanse Machinery Technology Co., Ltd. is a high-tech manufacturer specializing in concrete construction machinery, including laser screeds and related equipment. The company integrates R&D, production, and global sales, with products exported to over 60 countries and widely used in infrastructure projects worldwide.
Previous Post
Next Post
Related Articles
You Might Also Like
How long does it take to recover the investment in a laser leveling machine?
Concrete laser leveling machine is the most popular mechanical equipment in concrete floor construction nowadays. Many construction and floor construction units have purchased concrete laser leveling machines, because the labor cost saved by concrete laser leveling machine for construction and the wealth brought by it have been proved by countless users. For users who want to buy concrete laser leveling machine, a question they are more concerned about is how long it will take to recover the cost of the machine. In response to this problem, we summarized the before and after construction comparison of previous customers, and combined with the purchased equipment models and local market to conduct an analysis. Different concrete laser leveling machines have different prices, daily working areas and profits. Taking dz30-2 as an example, the construction area per hour is more than 300 square meters, and the daily workload can be completed in more than 2000 square meters to 2500 square meters. Taking the labor and cost saving of 4 yuan per square meter as an example, the daily profit is about 6000 yuan. If the project goes smoothly, the cost can be recovered in less than two months. Concrete laser leveling machine is suitable for large-area paving work. Through the connection with the power supply, the click generates power to drive the operation of the machine to complete the designated work and tasks. The independent transmitter arrangement of the laser leveling machine can complete large-area building paving, thereby effectively ensuring the consistency of other ground elevations. Moreover, the elevation is not controlled by the template, so the error caused by the machine construction is very small, which can effectively reduce the problem of construction joints and also minimize the subsequent maintenance costs.How to use the laser leveling machine? How many steps?
How to use the laser leveling machine? How many steps? The laser leveling machine manufacturer will introduce to you what to do with the equipment: check the equipment before using it to ensure that all functions of the equipment are normal, and adjust the reference point of the laser before it can be used , After paving, technicians are required to evaluate the ground, and it is completed only after the flatness is determined. 1. Preparation (1) After the base layer is processed, the equipment of the laser paver is debugged, and the fixed reference level point is drawn according to the original level point; the non-woven fabric is laid, the side formwork is supported, the laser transmitter is erected, and the ground is ground according to the original level point. The elevation is introduced into the laser leveling machine. (2) Conveying concrete Commercial concrete is used, and the commercial concrete is transported to the entrance and exit of the garage by tank truck, and then transported to the construction site by a three-wheel dump truck. (3) Standardization and verification Use a hand-held laser receiver to check the elevation of the floor, introduce the elevation into the laser paver, and adjust the reference point (±0.00) on the leveling machine. 2. Concrete paving Pouring steps: (1) After the formwork is supported, the warehouse should be cleaned and soaked with water one day in advance before pouring concrete. When pouring is approaching, drain the open water and sweep the cement slurry or interface agent. At this time, no obvious water accumulation is strictly prohibited. If there is, it must be resolutely removed before paving concrete. (2) After the concrete is put down, it should be preliminarily leveled, and the leveling height should be 3 cm thicker than the elevation. Then level it with a laser paver. The corners that cannot be leveled can be leveled with a gasoline leveler or manually. (3) When the warehouse near the wall is being poured, after the leveling machine walks over, it must be leveled with a scraper in time. and so on. (4) For areas where concrete mixer trucks cannot be driven to the site, tractors should be used to transfer concrete. After the pouring is completed, the floor finishing construction begins when the concrete is initially set. (5) When the warehouse near the wall is pouring, after the leveling machine walks over, it must be scraped with a scraper in time. and so on. (6) For areas where concrete mixer trucks cannot be driven to the site, tractors should be used to transfer concrete. After the pouring is completed, the floor finishing construction begins when the concrete is initially set. 3. During construction, the laser signal received by the receiver of the laser paver (frequency of 10 times per second) automatically adjusts the elevation in real time to ensure that the construction elevation is always at the set standard. Because the laser transmitter is fixed after being set up, it can ensure that the construction of a large area of ground does not produce cumulative errors. 4. During the construction, the operator uses a hand-held laser receiver to detect the ground after the machine is constructed, and again ensures that the flatness error is within the controllable range. A complete and perfect brand of course needs good word-of-mouth from local users, and the establishment of word-of-mouth requires long-term accumulation. If you want to be a good company, you must be responsible for customers and think about customers, and bring profits to customers better. This is the most important thing.What level of (FF) Floor Flatness and (FL) Floor Levelness can a concrete laser leveling machine guarantee
The concrete laser leveling machine, often called a Laser Leveling, can achieve significantly higher Floor Flatness (FF) and Floor Levelness (FL) numbers compared to traditional manual methods. While the maximum guaranteed level can depend on the specific machine, operator skill, slab preparation, and concrete mix, here is a general breakdown of the guaranteed capabilities and the high-end results that can be achieved: Laser Leveling routinely achieve floor tolerance specifications that fall into the "Flat" to "Very Flat" range, meeting or exceeding what is required for most industrial and commercial projects. FF/FL Classification FF (Flatness) Range FL (Levelness) Range Typical Application Laser Leveling Capability Moderately Flat FF 25 FL 20 General-purpose slab-on-grade Easily Exceeded Flat FF 35 FL 25 Standard warehouses, retail, offices Routine Minimum Very Flat FF 45 FL 35 Warehouses with high-lift forklifts (over 15-20 ft) Routinely Achieved Super Flat FF 50 and higher FL 40 and higher Robotics, Automated Guided Vehicles (AGVs), high-speed racks, TV studios, ice rinks High-End Capability Routine Performance: A good laser Leveling operation can routinely achieve FF 45 / FL 35 or better. Many industrial floors finished with a laser Leveling aim for and achieve FF 50+ / FL 40+. Accuracy (Deviation): Some manufacturers state a high-precision laser Leveling can achieve millimeter-level accuracy for leveling, or an overall flatness accuracy within about 3mm on industrial floors. Maximum Potential: With the latest technology (including 3D laser guidance systems) and meticulous finishing, projects have reported achieving FF 90+ / FL 85+, which is considered Super Flat and is necessary for advanced automated warehouse systems. The F-Number system (ASTM E1155) provides a standardized way to measure the quality of a concrete floor. FF (Floor Flatness): Measures the local bumpiness or waviness of the surface over a short distance (typically a 2-foot interval). This is controlled primarily by the finishing operations after the concrete is placed. Higher FF numbers mean a smoother surface. FL (Floor Levelness): Measures the conformity of the floor to the specified elevation or slope over a longer distance (typically a 10-foot interval). This is controlled mainly by the accuracy of the Leveling machine. Higher FL numbers mean a more level floor. Feature Impact on FF/FL Laser Guidance Ensures the Leveling head maintains a precise and consistent elevation across the entire slab, directly improving the FL (Levelness) number. Integrated Vibrator Provides consistent, high-frequency vibration and compaction across the full width of the Leveling head, reducing the surface defects and local variations that affect the FF (Flatness) number. Would you like me to find out the standard FF/FL requirements for a specific type of building, such as a warehouse or a sports facility? Note: The parameters provided in this document are for reference only and are not mandatory. Due to differences in technical characteristics between different brands and models of laser levelers, please consult the manufacturer for a suitable solution before actual operation. This reference document assumes no responsibility for any issues arising from failure to follow the manufacturer's instructions.
